serwis elektroniki  
 
 

Elektronika

Forum dyskusyjne dla elektronik i użytkowników sprzętu Audio Video
Obecny czas: Pią Mar 29, 2024 1:08 am

Wszystkie czasy w strefie UTC + 2 godziny




Napisz nowy temat Odpowiedz  [ 4 posty(ów) ] 
Autor Wiadomość
 Temat postu: Sony SLV-E580
PostWysłany: Czw Maj 31, 2007 6:39 pm 
Offline
Senior Member
Senior Member

Dołączenie: Pią Maj 11, 2007 4:54 pm
Postów: 147
Miejscowość: Kielce
Mam takie pytanie. Jak uruchomić tryb serwisowy w tym magnetowidzie, i czy da się tam przeprowadzić test przełączania się głowic?


Góra
 Profil  
 

elektronika



 Temat postu:
PostWysłany: Sob Cze 02, 2007 6:05 pm 
Offline
Senior Member
Senior Member

Dołączenie: Czw Maj 11, 2006 4:32 pm
Postów: 130
Miejscowość: Trzebnica
Mam taką serwisówkę, oto co piszą:
Cytuj:
SERVO SYSTEM Adjustment
RF Switching Position Adjustment
Purpose:
Adjust the interval between A ch and B ch of tape playback output.
Improve the interchangeability with other tapes and sets.
When it is out of order, the interval appears on the screen, the screen is disturbed.
Measurement Point : CH1: VIDEO LINE OUT, CH2: Pin 2 of CN261(RP-230 board) (RF SWP)
Adjusting Method:
1) Connect RP-230 board Pin 5 of CN261 to the GND for about 1 secont to activate the RF switching position adjustment mode.
2) Check appear “A P” on FL display.
3) Using the channel + and – buttons, adjust to 416 ± 32 µsec
(6.5 ± 0.5 H).
4) Press the pause button.
2-4. VIDEO SYSTEM ADJUSTMENT
Adjust the video system in the following sequence as a rule. The color video signal supplied from the pattern generator is used as a video input signal for video system adjustment in the recording mode.


Góra
 Profil  
 
 Temat postu:
PostWysłany: Sob Cze 02, 2007 10:17 pm 
Offline
Senior Member
Senior Member

Dołączenie: Pią Maj 11, 2007 4:54 pm
Postów: 147
Miejscowość: Kielce
Igor-b napisał(a):
Mam taką serwisówkę, oto co piszą:
Cytuj:
SERVO SYSTEM Adjustment
RF Switching Position Adjustment
Purpose:
Adjust the interval between A ch and B ch of tape playback output.
Improve the interchangeability with other tapes and sets.
When it is out of order, the interval appears on the screen, the screen is disturbed.
Measurement Point : CH1: VIDEO LINE OUT, CH2: Pin 2 of CN261(RP-230 board) (RF SWP)
Adjusting Method:
1) Connect RP-230 board Pin 5 of CN261 to the GND for about 1 secont to activate the RF switching position adjustment mode.
2) Check appear “A P” on FL display.
3) Using the channel + and – buttons, adjust to 416 ± 32 µsec
(6.5 ± 0.5 H).
4) Press the pause button.
2-4. VIDEO SYSTEM ADJUSTMENT
Adjust the video system in the following sequence as a rule. The color video signal supplied from the pattern generator is used as a video input signal for video system adjustment in the recording mode.


Okay! fajnie widze,że jest servo adjustmant, ale jak się dostać do trybu serwisowego w tym magnetowidzie?


Góra
 Profil  
 
 Temat postu:
PostWysłany: Pon Cze 04, 2007 4:14 pm 
Offline
Tech Support
Tech Support
Awatar użytkownika

Dołączenie: Śro Maj 17, 2006 10:30 pm
Postów: 253
Miejscowość: Jawor
Cytuj:
Connect RP-230 board Pin 5 of CN261 to the GND for about 1 secont to activate the RF switching position adjustment mode.

Z opisu wynika, że trzeba zewrzeć 5 pin CN261 złącza RP-230 do masy na 1 sekundę to przejdzie w tryb "adjustment mode"


Góra
 Profil  
 
Wyświetl posty z poprzednich:  Sortuj według  
Napisz nowy temat Odpowiedz  [ 4 posty(ów) ] 

Wszystkie czasy w strefie UTC + 2 godziny


Kto jest online

Użytkownicy przeglądający to forum: Brak zarejestrowanych użytkowników oraz 9 gości

Polecamy - Porady prawne: Adwokat Warszawa


Nie możesz zakładać nowych tematów na tym forum
Nie możesz odpowiadać w tematach na tym forum
Nie możesz edytować swoich postów na tym forum
Nie możesz usuwać swoich postów na tym forum

Szukaj:
cron
Powered by phpBB © 2000 - 2018 phpBB Group
[ Time : 0.062s | 13 Queries | GZIP : Off ]


Naprawa telewizorów